Tesla HVP Alert Codes

Tesla alert code in the High Voltage Protection (HVP) module. The high voltage (HV) system has reported an over-current condition. When this condition is detected, the pyro disconnect is fired to protect the HV battery, the vehicle, and the vehicle?s immediate environment from potential damage.

Tesla warning code in the High Voltage Protection (HVP) module related to watchdog reset.

Tesla warning code in the High Voltage Protection (HVP) module related to unused alert2.

Tesla warning code in the High Voltage Protection (HVP) module related to sw assertion.

Tesla warning code in the High Voltage Protection (HVP) module related to over dchg current fault.

Tesla warning code in the High Voltage Protection (HVP) module. Warns if the pack charge current is above max charge current limit The pack charge current is above max charge current limit for X duration (in msec) The pack charge current is below max charge current limit The DC charging will end and contactors may open immdediately or pyro may disconnect Warns if the CP ECU has faulted These charging will not be allowed Sets if an HVIL fault is detected. Contactors cannot close (car will no longer drive) if the contactors are currently open. If no repairs were performed and the alert clears on its own, there is risk of reoccurrence. The HVIL is broken or HVIL nodes are lower than expected Contactors will not close, it may open if vehicle not in drive Warn if pack contactor enter to the BLOCKED state Warns if the Energy reserve voltage supply is below minimum voltage threshold The Energy reserve voltage supply is below minimum voltage threshold The Energy reserve voltage supply is above minimum voltage threshold The pyro diagnostics may fail, the contactors will not close warn if harware triggers to blow the pyro This is an indication that pyro was blown The HVP config block may be missing, incorrect, or unsupported The HVP is unable to initialize configuration parameters

Tesla warning code in the High Voltage Protection (HVP) module related to over current fault.

Tesla warning code in the High Voltage Protection (HVP) module related to over temperature fault.

Tesla warning code in the High Voltage Protection (HVP) module related to over voltage fault.

Tesla warning code in the High Voltage Protection (HVP) module related to under voltage fault.

Tesla warning code in the High Voltage Protection (HVP) module related to primary bmb mia fault.

Tesla warning code in the High Voltage Protection (HVP) module related to bms mia on hvi fault.

Tesla warning code in the High Voltage Protection (HVP) module. The CP node is mia on HVS CAN The pyro fuse will blow

Tesla warning code in the High Voltage Protection (HVP) module related to pcs mia fault.

Tesla warning code in the High Voltage Protection (HVP) module related to gtw mia fault.

Tesla warning code in the High Voltage Protection (HVP) module. The CP ECU has faulted The CP ECU is not faulted

Tesla warning code in the High Voltage Protection (HVP) module. Contactor state is open

Tesla warning code in the High Voltage Protection (HVP) module related to pyro mia fault.

Tesla warning code in the High Voltage Protection (HVP) module related to pyro mia warning.

Tesla warning code in the High Voltage Protection (HVP) module related to supply12v fault.

Tesla warning code in the High Voltage Protection (HVP) module related to ver supply fault.

Tesla warning code in the High Voltage Protection (HVP) module. The HVIL is intact

Tesla warning code in the High Voltage Protection (HVP) module related to bms mia on hvs fault.

Tesla warning code in the High Voltage Protection (HVP) module. Warns if the pack voltage doesn't match approximately with sum of brick voltages The pack voltage doesn't match approximately with sum of brick voltages The pack voltage match approximately with sum of brick voltages The contactors may not be allowed to close Alerts if PyroLeakTest pyro diagnostic has cross warning threshold PyroLeakTest sees an Aout outside of 15% tolerance when measuring leakage Customer Facing text to seek service immediately Warns if the BMS node is mia on HVS CAN The BMS node is mia on HVS CAN The BMS node is not mia on HVS CAN Warn if FC contactors are forced open

Tesla warning code in the High Voltage Protection (HVP) module. Pack contactor state is open

Tesla warning code in the High Voltage Protection (HVP) module related to pack pos ctr arc fault.

Tesla warning code in the High Voltage Protection (HVP) module related to pack neg ctr arc fault.

Tesla warning code in the High Voltage Protection (HVP) module. Warns if the HVP detectes both BMS and Shunt MIA while pack contactors closed If the HVP detectes both BMS and Shunt MIA while pack contactors closed When either BMS or Shunt is not mia Alerts if the HV pyro fuse is blown One of many critical HVP or BMS alert, log data contains the reason Clears after a pyro loop is completed and meets expectation Warns if the shunt current reading is not avaialble The shunt current reading is not avaialble The shunt current reading is avaialble Current readings are not avaialble

Tesla warning code in the High Voltage Protection (HVP) module related to fc cont hw fault.

Tesla warning code in the High Voltage Protection (HVP) module. The CP version mismatch The CP version match expected

Tesla warning code in the High Voltage Protection (HVP) module related to pack cont hw fault.

Tesla warning code in the High Voltage Protection (HVP) module related to pyro fuse blown.

Tesla warning code in the High Voltage Protection (HVP) module. HV is disconnected

Tesla warning code in the High Voltage Protection (HVP) module. The CPIL loop is complete

Tesla warning code in the High Voltage Protection (HVP) module. Warn if a pack contactor falls open during closed state Warns if the ENS line is not connected to HVC The ENS line is not connected to HVC ENS idle signal is detected on ENS line The crash signal may not be detected by HVP

Tesla warning code in the High Voltage Protection (HVP) module related to fc contactor fell open.

Tesla warning code in the High Voltage Protection (HVP) module related to pack ctr close blocked.

Tesla warning code in the High Voltage Protection (HVP) module related to fc ctr close blocked.

Tesla warning code in the High Voltage Protection (HVP) module. Warn if pack contactors are forced open Warns if the BMS node is mia on HVI CAN The BMS node is mia on HVI CAN The BMS node is not mia on HVI CAN CAN messages are not received from BMS or other nodes on vehicle Warns if the HVP detects unintended loss of contactor control (V or I) The HVP detects loss of contactor power or coil current Contactor power or coil current is dropped below threshold The contactors opens unintentionally Warns if the voltage and temperature readings from primary BMB chain are mia The voltage and temperature readings from primary BMB chain are mia The voltage and temperature readings from primary BMB chain are not mia The secondary bmb chain is used exclusively for voltage and temperature protoection Alerts if any of the pyro diagnostic has failed or the pyro has blown One of many pyro diagnostic has failed including the pyro having blown Clears after all the diagnostic has passed Sorry, Contactors are not allowed to close. Warn if pack contactors are not allowed to close This meta alert will set if any of the reasons for preventing contactors to close (listed in this alert payload) are still present. This alert is always set with an accompanying alert that provides more specific information for the fault. Pack contactor blocking condition is cleared While this alert is set, HV contactors will not be able to close. This will prevent drive, charge and 12V support and eventually the 12V battery will be fully discharged and the vehicle will go offline. The PCS node is mia on HVS CAN The PCS node is not mia on HVS CAN CAN messages are not received from PCS node Warn if FC contactors are not allowed to close FC contactor blocking condition is cleared warn if shunt temerature exceeds high threshold value shunt temperature falls below low threshold value This is an indication that there could be a high impedance joint and prolonged time at this temp could affect the properties of the manganin Warn if the CPIL fault is detected Warns if the HVP detects series arc at FC contactor The HVP detects series arc at FC contactor The arc condition is not detected at FC contactor Warns if the CP version mismatch HVP cannot trust the CP indication, thus it is not safe to charge warn if if the thermistor sense line is not connected This is an indication that shunt thermistor is not in place/missing/bad Warns if the crash signal is detected by HVP The crash signal is detected by HVP The ENS idle siganl is detected on ENS line Warns if the low voltage battery is below minimum voltage threshold The low voltage battery is below minimum voltage threshold The low voltage battery is above minimum voltage threshold The contactors may not remain closed A brick voltage is below minimum voltage limit A brick voltage is below minimum voltage limit for X duration (in seconds) All brick voltages are above minimum voltage limit The conactors may open immdediately or pyro fuse may blow The Gateway node is mia on HVS CAN The Gateway node is not mia on HVS CAN CAN messages are not received from Gateway node Warns if the pack current (discharge or charge) is above max current limit. The pack current (discharge or charge) is above max current limit. The pack current (discharge or charge) is below max current limit. Warns if the pack discharge is above max discharge current limit The pack current is above max discharge current limit for X duration (in msec) The pack current is below max discharge current limit The contactors will open immdediately or pyro fuse may blow A pack module temperature is above maximum temperature limit A pack module temperature is above maximum temperature limit for X duration (in seconds) All pack module temperatures are below maximum temperature limit The HVP part number may be missing, incorrect, or unsupported The HVP is unable to initialize parameters related to PCBA configuration Warns if the HVP detects series arc at pack contactor The HVP detects series arc at pack contactor The arc condition is not detected at pack contactor A brick voltage is above maximum voltage limit All brick voltages are below maximum voltage limit

Tesla warning code in the High Voltage Protection (HVP) module. FC contactor state is open

Tesla warning code in the High Voltage Protection (HVP) module related to dc link over voltage.

Tesla warning code in the High Voltage Protection (HVP) module related to shunt over temperature.

Tesla warning code in the High Voltage Protection (HVP) module related to passive pyro deploy.

Tesla warning code in the High Voltage Protection (HVP) module related to pack ctr close failed.

Tesla warning code in the High Voltage Protection (HVP) module related to fc ctr close failed.

Tesla warning code in the High Voltage Protection (HVP) module related to shunt thermistor mia.

Tesla warning code in the High Voltage Protection (HVP) module. Pack voltage differs from DC Link voltage too much with contactors closed Warn if DC-link voltage is above over voltage threshold while closing contactors Contactors closing will be aborted Warn if FC contactor enter to the BLOCKED state

Tesla warning code in the High Voltage Protection (HVP) module related to sw missing config block.

Tesla warning code in the High Voltage Protection (HVP) module related to sw missing part number.

Tesla alert code in the High Voltage Platform module. High Voltage Power System Fault

Tesla alert code in the High Voltage Platform module. High Voltage Isolation Fault Detected

Tesla alert code in the High Voltage Platform module. High Voltage System Shutdown Initiated